The effect of immersion disinfection procedures on dimensional stability of two elastomeric impression materials.
(25/64)
The aim of this study was to determine the effect of immersion disinfection procedures on the dimensional stability of two elastomeric impression materials. Impressions of a stainless steel die were made with polyether (PE) and with addition-polymerized silicone rubber (PVS). The test specimens underwent disinfection treatment by immersion in two commercially available solutions containing quaternary ammonium compounds (Sterigum Powder, SP) and glutaraldehyde plus an amino derivative (MD520, MD), respectively. The impressions were measured at 4 different time points: before any disinfection treatment (T0); after the first disinfection (T1); 6 hours after the first disinfection (T2); after the second disinfection, carried out 6 hours after the first one (T3). Impressions which were not disinfected served as controls. When both impression materials were disinfected with SP, significant differences were detected among all measurements (P < 0.0001), with the exception of T2 vs T3 (P > 0.05). On the other hand, when MD was used, significant differences were found when T0 measurement was compared to T1, T2 and T3 measurements (P = 0.0043 for PE, and P = 0.0014 for PVS). The dimensional change of all material/disinfectant combinations was always +info)
Should preclinical typodonts be disinfected prior to grading?
(26/64)
This is a report of a unique finding in a preclinical laboratory that may be a potential dental school health hazard. Visual inspection (conducted in April 2008 by a preclinical crown and bridge course coordinator) of typodonts used by second-year students at the University of Mississippi School of Dentistry found that fourteen out of thirty-nine had black spots on the undersurface of the cheek shroud and/or plastic gingiva. The spots were cultured by the Medical Center's Department of Microbiology and described only as being mold/fungus typical of that which frequently grows in warm, moist, southern environments. Although indoor molds are common, about 5 percent of the general population will develop some type of mild allergic airway problem from molds over their lifetime. Mold on typodonts is unsightly, indicates failure of students to recognize the value of cleanliness in the dental environment, and may be a potential health hazard for some individuals. Cleaning and drying procedures for typodonts were implemented. The transfer of items between students and instructors during preclinical courses provides many opportunities for the spread of potentially harmful microorganisms/viruses. As a minimal level of personal protection, it is suggested that instructors wear disposable gloves and face masks and exercise hand washing between handling student instruments and typodonts. This problem has not been previously mentioned in the literature and merits further investigation/discussion. (+info)
Resistance to disinfection of a polymicrobial association contaminating the surface of elastomeric dental impressions.
(27/64)
The aim of this study was to evaluate the ability to resist disinfection of a polymicrobial association contaminating the surface of dental impressions obtained with two different elastomers: a polyether (Impregum) and an addition-polymerized silicone (Elite). Impressions were contaminated with a mixture of three biofilm-forming microorganisms (Staphylococcus aureus, Pseudomonas aeruginosa and Candida albicans) and disinfected immediately after contamination, or after microbial layers were allowed to develop during a six-hour storage. Two commercial disinfectants were tested: MD 520 containing 0.5% glutaraldehyde and Sterigum Powder without glutaraldehyde. Residual contamination was recovered by mechanical rinsing immediately after disinfection and after a six-hour storage of disinfected impressions, and assessed by colony counting. Both disinfectants tested were shown to be effective in reducing the microbial presence on the impression materials, achieving at least a 102 reduction of microbial counts compared to water rinsing. However, Sterigum was generally less effective on the Elite elastomer and could not grant disinfection on six-hour aged P. aeruginosa and C. albicans microbial layers. The results of this study suggest that the materials used for the impressions influence the efficacy of disinfection. Disinfectants should be tested according to conditions encountered in everyday clinical practice and the need for immediate disinfection of impressions should be clearly indicated by manufacturers. (+info)
In vitro antifungal action of different substances over microwaved-cured acrylic resins.
(28/64)