In vitro comparison of the retention capacity of new aesthetic brackets.
(1/103)
Tensile bond strength and bond failure location were evaluated in vitro for two types of aesthetic brackets (non-silanated ceramic, polycarbonate) and one stainless steel bracket, using bovine teeth as the substrate and diacrylate resin as the adhesive. The results show that metallic bracket had the highest bond strength (13.21 N) followed by the new plastic bracket (12.01 N), which does not require the use of a primer. The non-silanated ceramic bracket produced the lowest bond strength (8.88 N). Bond failures occurred mainly between bracket and cement, although a small percentage occurred between the enamel-cement interface with the metal and plastic brackets and within the cement for the plastic bracket. With the ceramic bracket all the failures occurred at the bracket-cement interface. This suggests that the problems of enamel lesions produced by this type of bracket may have been eliminated. The results also show that the enamel/adhesive bond is stronger than the adhesive/bracket bond in this in vitro study. (+info)
Virus passage through track-etch membranes modified by salinity and a nonionic surfactant.
(2/103)
Why do viruses sometimes not pass through larger pores in track-etch filters? Increasing the salinity (0.8 to 160 mM Na+) decreased phiX174 and PRD1 passage through track-etch polycarbonate membranes (sodium dodecyl sulfate coated but not polyvinylpyrrolidone coated) and PRD1 passage through polyester membranes. Undiminished passage when 0.1% Tween 80 was added implied that nonionic virus adsorption occurred and indicated that high levels of salinity decreased virus passage by decreasing electrostatic repulsion that prevented adsorption. (+info)
Magnetic bead capture eliminates PCR inhibitors in samples collected from the airborne environment, permitting detection of Pneumocystis carinii DNA.
(3/103)
PCR detection methods are useful in studies of organisms not amenable to culture. Inhibitors in environmental samples can interfere with such assays. We describe a magnetic bead DNA capture protocol that removes inhibitors from outdoor air samples, maintaining the sensitivity of a 16S Pneumocystis carinii mitochondrial rRNA gene-based PCR. (+info)
The relationship between the difference in prismatic refractive power of an eye-and-face protector and its thickness, radius of curvature, and material.
(4/103)
With the help of the research results presented here and on the basis of a graphic analysis we aim to prove the existence of a relationship between the difference in prismatic refractive power and the thickness, curvature radius, and type of material used for panoramic oculars in protective spectacles, goggles, and face shields. The difference in the prismatic refractive power is a fundamental optical characteristic of a protective ocular without corrective effect. According to Standard No. EN 165:1995 (European Committee for Standardization, 1995) the difference in the prismatic refractive power is a difference in the prismatic effect at 2 observation points of an eye-protector. (+info)
Mammalian neural tube grafting experiments: an in vitro system for mouse experimental embryology.
(5/103)
We have developed a simple experimental technique which consists of explanting the mouse embryo anterior neural tube--the presumptive brain anlage--onto polycarbonate membranes. The neural epithelium of the explants maintained both its original topology and topography for at least two days in culture. Analysis of cell death in the explants by assaying propidium iodide uptake showed high viability of neuroepithelial cells during the culture period. Both the pattern of gene expression and the initial steps of neural cellular differentiation were well preserved, being similar to those which occur in the normal in vivo situation. We show here two applications of this tissue culture technique which is similar to that which has been previously employed for avian embryo models. The first involves neuroepithelial grafting experiments by heterotopic transplantation of the zona limitans intrathalamica (ZLI) into the mesencephalon and the second consists of fibroblast growth factor (FGF8) protein interaction studies using soaked bead insertions. This in vitro system constitutes a powerful experimental embryological tool which can have other applications including time-lapse imaging and electrophysiology. (+info)
Content and release of bisphenol A from polycarbonate dental products.
(6/103)
Bisphenol A (BPA) is an endocrine disruptor, and is used as a raw material for bisphenol A diglycidyl methacrylate and polycarbonate, that are used in the dental materials. In this study, the total and released amounts of BPA from polycarbonate-based dental materials were measured with high-pressure liquid chromatography (HPLC). The specimens used were orthodontic brackets and denture base resins in the same condition as when obtained commercially were cut into 3 x 3 x 4 mm pieces and crushed into powder. The HPLC analysis was carried out after immersion of the specimens in water or ethanol for a determined time. The total amount of BPA in the specimens was analyzed after dissolution in chloroform. The amount of BPA released after immersion in water for 1 hr was 0.01-0.4 microgram/g for the block samples and 0.14-4.22 micrograms/g for the crushed samples, while that in ethanol for 1 hr was 0.12-9.42 micrograms/g for the block samples and 0.42-22.24 micrograms/g for the crushed samples. The control of BPA in the denture preform resin was 78.9 micrograms/g and this increased to 90.2 micrograms/g after heating to form dentures and then to 250 micrograms/g with mechanical crushing. The results of this study indicate that BPA is released from polycarbonates used in dentistry, and that the thermal conditions during the manufacturing of restorations may cause polymer decomposition resulting in the formation of BPA. (+info)
Change in the bisphenol A content in a polycarbonate orthodontic bracket and its leaching characteristics in water.
(7/103)
The change in the bisphenol A (BPA) content in a polycarbonate (PC) orthodontic bracket and its leaching characteristics were studied by immersing the bracket in water because BPA has been the matter of controversy in dentistry due to its estrogenic potential. PC brackets were placed in water at 37 degrees C and 60 degrees C and the BPA content in the bracket and the amount of BPA released into the water were analyzed at appropriate intervals by high performance liquid chromatography. The BPA content increased in the water with time and was 3.8-fold after 12 months at 37 degrees C and 12.4-fold after 14 weeks at 60 degrees C compared with the virgin value. The rate of BPA release also increased with time. The results suggested that BPA was released from the bracket time-dependently in the oral cavity. However, it was assessed that little or no estrogenic effect due to the released BPA is expected in the human body. (+info)
Crowns and other extra-coronal restorations: try-in and cementation of crowns.
(8/103)
Having successfully negotiated the planning, preparation, impression and prescription of your crown, the cementation stage represents the culmination of all your efforts. This stage is not difficult, but a successful outcome needs as much care as the preceding stages. Once a restoration is cemented there is no scope for modification or repeat You have to get it right first time. Decemented crowns often have thick layers of residual cement suggesting problems with either initial seating or cement handling. When the fate of restorations costing hundreds of pounds depends on correct proportioning of cements and the quality of the mix, the value of a well-trained and experienced dental nurse is easy to see. Both dentist and nurse need a working knowledge of the materials they are handling. (+info)