Asymptomatic radiopaque lesions of the jaws: a radiographic study using cone-beam computed tomography.
(67/97)
Panoramic radiography and cone-beam computed tomography (CT) were used to analyze asymptomatic radiopaque lesions in the jaw bones and determine the diagnostic relevance of the lesions based on their relationships to teeth and site of origin. One hundred radiopaque lesions detected between 1998 and 2002 were examined by both panoramic radiography and cone-beam CT. On the basis of panoramic radiographs, the region was classified as periapical, body, or edentulous, and the site was classified as molar or premolar. Follow-up data from medical records were available for only 36 of these cases. The study protocol for simultaneous use of cone-beam CT was approved by the ethics review board of our institution. A large majority of radiopaque lesions were observed in premolar and molar sites of the mandible; 60% of lesions were periapical, 24% were in the body, and 16% were in the edentulous region. An interesting type of radiopaque lesion, which we named a pearl shell structure (PSS), was observed on cone-beam CT in 34 of the 100 lesions. The PSS is a distinctive structure, and this finding on cone-beam CT likely represents the start of bone formation before bone sclerosis. (+info)
Nasal floor augmentation for the reconstruction of the atrophic maxilla: a case series.
(68/97)
Evaluation of mandibular bone mineral density using the dual-energy X-ray absorptiometry technique in edentulous subjects living in an endemic fluorosis region.
(69/97)
Evaluation of a complete denture trial method applying rapid prototyping.
(70/97)
A new trial method for complete dentures using rapid prototyping (RP) was compared with the conventional method. Wax dentures were fabricated for 10 edentulous patients. Cone-beam CT was used to scan the wax dentures. Using 3D computer-aided design software, seven 3D denture images with different artificial teeth arrangements were made and seven trial dentures per patient were fabricated accordingly. Two prosthodontists performed a denture try-in for one patient using both conventional and RP methods. The prosthodontists and patients rated satisfaction for both methods using a visual analogue scale. Satisfaction ratings with both conventional and RP methods were compared using the Wilcoxon signed-rank test. Regarding prosthodontist's ratings, esthetics and stability were rated significantly higher with the conventional method than with the RP method, whereas chair time was rated significantly longer with the RP method than with the conventional method. Although further improvements are needed, the trial method applying RP seems promising. (+info)
The influence of exposure parameters on jawbone model accuracy using cone beam CT and multislice CT.
(71/97)
OBJECTIVE: The main purpose of this study was to investigate the influence of exposure parameters on jawbone model accuracy when using cone beam CT (CBCT) and multislice CT (MSCT). METHODS: A lower and an upper edentulous human cadaver jaw were scanned using micro-CT (Skyscan 1173 high energy spiral scan micro-CT; Skyscan NV, Kontich, Belgium) at 35 mum to serve as true reference. The in vitro samples were exposed using six CBCT units and one MSCT system. CBCT exposure protocols were chosen according to clinically available settings. The variables were kilovoltage, milliamperage, voxel size and/or scan time. Image segmentation was based on local thresholds using profile lines. The resulting jawbone segmentations were registered with the reference and image processing was done to internally fill the segmentations. A point-based distance calculation was performed between the three-dimensional objects and reference scans and deviation percentages were calculated for 2 mm, 1 mm and 0.5 mm intervals. RESULTS: All points of the MSCT surface models lay within a 1 mm deviation range and 98.5% within 0.5 mm compared with micro-CT. For the different CBCT systems, accuracy came close to MSCT with mean percentages of 98.9% within 1 mm deviation and 92.8% within 0.5 mm. A difference of approximately 1% between lower and upper jaws could be perceived. For the specific CBCT exposure protocols, only scan time and voxel size revealed certain significant differences. CONCLUSION: Jawbone model accuracy using CBCT was comparable with MSCT. The surface models of the upper jaws deviated slightly more than those for lower jaws. CBCT exposure settings had a limited influence on accuracy with scan time and voxel size as the main factors. (+info)
Implications of edentulism on quality of life among elderly.
(72/97)