The relationship between stem subsidence and improvement in the radiolucency in polished tapered stems.
(65/386)
We studied the relationship between stem subsidence and improvement in the initial radiolucency at the bone-cement interface in polished- and rough-surface stems. Stem subsidence was seen in 34 of 42 hips (81.0%), and improvement in the initial radiolucency was seen in 15 hips (35.7%) in collarless polished tapered stems at 1 year after operation. In polished stems, stem subsidence in cases with improvement in the initial radiolucency was significantly greater than in those with no change (average 1.12 mm and 0.48 mm, P<0.005). In rough-surface stems partially coated with polymethylmethacrylate (VerSys Cemented Plus), no stem subsidence and no improvement in the initial radiolucency was seen. In polished stems, stem subsidence leads to cement creep and compressive force on the bone-cement interface and can improve the initial radiolucency. (+info)
Removal resistance of glass-fiber and metallic cast posts with different lengths.
(66/386)
This study evaluated the strength required to remove glass-fiber and metallic cast posts with different lengths. Sixty endodontically treated canines were included and their roots were embedded in acrylic resin after discarding the crowns. Samples were randomly assigned to 3 groups according to the post length (n = 20): I- 6 mm, II - 8 mm and III- 10 mm. Each group was divided into 2 subgroups based on the post material (n = 10): A- glass fiber or B- metallic cast. Post-space was prepared with Fibrekor Post Kit attached to a parallelometer. In subgroup A, prefabricated glass fiber posts from Fibrekor Post Kit were utilized. In metallic post group (subgroup B), an impression of post space was obtained, followed by casting. All posts were luted with Panavia F cement. A universal testing machine determined the force required to dislodge each post. ANOVA analysis indicated significant differences (P < 0.01) among post length. Tukey test showed that posts with 10 mm-length showed higher resistance on removal than posts with 6 mm-length. Posts with 8 mm-length did not exhibit difference when compared to 6 and 10 mm posts. No significant differences (P > 0.05) were observed between the tested post materials. It was concluded that the type of post did not influence the removal resistance and that posts with 10 mm-length required greater force to be dislodged. (+info)
Acetabular revision with morsellised allogenic bone graft and a cemented metal-backed component.
(67/386)
Failure of total hip arthroplasty with acetabular deficiency occurred in 55 patients (60 hips) and was treated with acetabular revision using morsellised allograft and a cemented metal-backed component. A total of 50 patients (55 hips) were available for clinical and radiological evaluation at a mean follow-up of 5.8 years (3 to 9.5). No hip required further revision of the acetabular component because of aseptic loosening. All the hips except one had complete incorporation of the allograft demonstrated on the radiographs. A complete radiolucent line of > 1 mm was noted in two hips post-operatively. A good to excellent result occurred in 50 hips (91%). With radiological evidence of aseptic loosening of the acetabular component as the end-point, the survivorship at a mean of 5.8 years after surgery was 96.4%. The use of impacted allograft chips in combination with a cemented metal-backed acetabular component and screw fixation can achieve good medium-term results in patients with acetabular bone deficiency. (+info)
Peri-prosthetic bone mineral density after total knee arthroplasty. Cemented versus cementless fixation.
(68/386)
We compared peri-prosthetic bone mineral density between identical cemented and cementless LCS rotating platform total knee arthroplasties. Two matched cohorts had dual energy x-ray absorptiometry scans two years post-operatively using a modified validated densitometric analysis protocol, to assess peri-prosthetic bone mineral density. The knee that was not operated on was also scanned to enable the calculation of a relative bone mineral density difference. Oxford Knee and American Knee Society scores were comparable in the two cohorts. Statistical analysis revealed no significant difference in absolute, or relative peri-prosthetic bone mineral density with respect to the method of fixation. However, the femoral peri-prosthetic bone mineral density and relative bone mineral density difference were significantly decreased, irrespective of the method of fixation, particularly in the anterior distal portion of the femur, with a mean reduction in relative bone mineral density difference of 27%. There was no difference in clinical outcome between the cemented and cementless LCS total knee arthroplasty. However, both produce stress-shielding around the femoral implants. This leads us to question the use of more expensive cementless total knee components. (+info)
Acetabular reconstruction with impacted bone allografts and cemented acetabular components: a 2- to 13-year follow-up study of 142 aseptic revisions.
(69/386)
We reviewed the clinical and radiological results of 131 patients who underwent acetabular revision for aseptic loosening with impacted bone allograft and a cemented acetabular component. The mean follow-up was 51.7 months (24 to 156). The mean post-operative Merle D'Aubigne and Postel scores were 5.7 points (4 to 6) for pain, 5.2 (3 to 6) for gait and 4.5 (2 to 6) for mobility. Radiological evaluation revealed migration greater than 5 mm in four acetabular components. Radiological failure matched clinical failure. Asymptomatic radiolucent lines were observed in 31 of 426 areas assessed (7%). Further revision was required in six patients (4.5%), this was due to infection in three and mechanical failure in three. The survival rate for the reconstruction was 95.8% (95% confidence interval 92.3 to 99.1) overall, and 98%, excluding revision due to sepsis. Our study, from an independent centre, has reproduced the results of the originators of the method. (+info)
Biomechanics of the Birmingham hip resurfacing arthroplasty.
(70/386)
The effects of the method of fixation and interface conditions on the biomechanics of the femoral component of the Birmingham hip resurfacing arthroplasty were examined using a highly detailed three-dimensional computer model of the hip. Stresses and strains in the proximal femur were compared for the natural femur and for the femur resurfaced with the Birmingham hip resurfacing. A comparison of cemented versus uncemented fixation showed no advantage of either with regard to bone loading. When the Birmingham hip resurfacing femoral component was fixed to bone, proximal femoral stresses and strains were non-physiological. Bone resorption was predicted in the inferomedial and superolateral bone within the Birmingham hip resurfacing shell. Resorption was limited to the superolateral region when the stem was not fixed. The increased bone strain observed adjacent to the distal stem should stimulate an increase in bone density at that location. The remodelling of bone seen during revision of failed Birmingham hip resurfacing implants appears to be consistent with the predictions of our finite element analysis. (+info)
The design features of cemented femoral hip implants.
(71/386)
We undertook a review of the literature relating to the two basic stem designs in use in cemented hip replacement, namely loaded tapers or force-closed femoral stems, and the composite beam or shape-closed designs. The associated stem fixation theory as understood from in vitro studies and finite element modelling were examined with reference to the survivorship results for each of the concepts of fixation. It is clear that both design principles are capable of producing successful long-term results, providing that their specific requirements of stem metallurgy, shape and surface finish, preparation of the bone and handling of the cement are observed. (+info)
Influence of the tibial stem design on bone density after cemented total knee arthroplasty: a prospective seven-year follow-up study.
(72/386)
We prospectively measured the changes in bone mineral density (BMD) in the proximal tibia of 20 total knee arthroplasties, ten with cruciform stems and ten with cylindrical stems. The measurements were made one, four and seven years after surgery. We observed a uniform density decrease in three regions of interest from one to seven years of follow-up. Cylindrical stems showed an asymmetrical density decrease between the three regions of interest, with no change in the central region, a slight decrease in the lateral region, and large decrease in the medial region. Multivariate analysis with general linear model showed the stem type factor as statistically significant for medial region of interest (p = 0.006). The cylindrical stem produces heterogeneous BMD changes under the tibial platform in knee arthroplasties, and this could be a potential risk factor for asymmetrical subsidence of this component. (+info)